Exactly How To Install A Bath Tub (For Novices).
Exactly How To Install A Bath Tub (For Novices).
Blog Article
Right here in the next paragraph you might get more superb guidance in relation to Installing A Bathtub.
Installing a bath tub isn't precisely brain surgery, however it does call for solid plumbing, woodworking, and in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately hard job. If the old bathtub is easily available, the task can move immediately; if you have to open a wall surface to remove the old bathtub and also position the brand-new bathtub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to move out the old bathtub and also set in the new one. See to it you have certified yourself for the task and also are comfortable attempting it. As opposed to hiring a specialist to take over a halfway-completed project, it is far better to take into consideration utilizing one prior to you begin. Possibilities are you may require a specialist plumber to make tube links.
This short article will certainly aid you install a new tub in your bathroom if you have already gotten a brand-new bathtub and don't require to alter the setup of your previous water pipes.
Your tools and product list should comprise the following:
Planning for the Installation
Firstly, the supporting framework provided with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also practical to fit a supporting plate under the faucets system to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of both faucets utilizing 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its last placement.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is separate the water system. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be quite bothersome because of the restricted accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have actually been eliminated, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Prior to proceeding to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Setting up the Bathtub
Making use of the two wood boards under its feet, place the tub in the required setting. The wood boards are valuable in equally spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 little factors.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level and also adjusting the feet on the bathtub up until the level reviews level.
To mount taps, fit all-time low of the outermost flexible faucet adapter to the suitable supply pipe by making a compression sign up with; then do the very same for the other faucet.
Activate the supply of water as well as examine all joints and new pipework for leakages and tighten them if required. Load the tub as well as additionally check the overflow outlet as well as the regular outlet for leaks.
Ultimately, deal with the bath paneling as explained in the maker's user's manual. Tiling as well as securing around the tub needs to wait until the tub has actually been made use of at least once as this will resolve it right into its last position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin ensuring that the washers are in location between the tap as well as the sink. Secure the tap in place with the producer given backnut. Once the faucet is firmly in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap ports. The former kind needs to be attached to the faucet finishes first, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bath meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to break a rigid seal, causing the water to pass through the wall surface between the bath and the tiling, leading to complications with wetness as well as possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components and also fittings. They are sold in tubes and also cartridges, as well as are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched paper or soft rope. Remember to constantly fill up the bathtub with water prior to securing, to enable the movement experienced when the bathtub remains in use. The sealant can crack rather very early if you do not consider this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily readily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
I'm just very fascinated with A Step-by-Step Guide to Installing a Bathtub and I am hoping you liked our entry. In case you liked our blog posting please don't forget to pass it around. I value reading our article about How to Install a Bathtub.
Visit The Following Page Report this page